ISO Ingénierie
Focus area · Nuclear control & command

Environmental qualification

Seismic · EMC · Radiation · Temperature · Humidity - RCC-E & IEC 60780

Talk to an expert

Demonstrating that a piece of control & command equipment withstands the environmental constraints of a BNI takes more than a single test. ISO Ingénierie specifies the applicable conditions (seismic, EMC, radiation, temperature, humidity), builds the qualification plan, drafts the test procedures, analyses the laboratory results and consolidates the whole in a Qualification Summary Dossier (DSQ), the cornerstone piece of the safety file.

On nuclear safety-classified control & command systems, the demonstration of the environmental withstand of equipment is a major challenge, both technical and regulatory. The applicable baselines - RCC-E, IEC 60780, IEC 60980, IEC 61000 - impose a traceable approach that goes well beyond a simple laboratory test: each constraint must be specified, tested under representative conditions, analysed and documented.

ISO Ingénierie supports architect-integrators, BNI operators and equipment suppliers throughout this approach, through to the production of the Qualification Summary Dossier (DSQ), which is enforceable before the regulatory authorities.

Constraints covered

Cross-cutting expertise covering all environmental loads encountered in the nuclear sector.

Seismic

Seismic withstand for design-basis earthquakes, spectral response, shaker-table tests.

EMC

Electromagnetic compatibility: conducted/radiated emissions, RF immunity, electrostatic discharges.

Radiation

Resistance to ionising radiation (gamma, neutron) over the whole operational life of the equipment.

Temperature

Operation in extreme conditions, thermal cycles, withstand in degraded post-accident ambient conditions.

Humidity

Behaviour in humid atmospheres, IP protection, salt-mist withstand depending on the environment.

Other constraints

Ageing, shocks, mechanical vibrations, chemical environments specific to the installation.

Your needs

What you expect from a partner for qualifying your I&C equipment in a nuclear environment.

01

Precisely identify the full set of environmental conditions applicable to your equipment: seismic loads, EMC, radiation, temperature variations, humidity, or any other constraint specific to its real operating environment.

02

Have at your disposal a structured, documented and traceable qualification approach that comprehensively covers the environmental requirements expected on a safety-classified system, with no grey areas.

03

Make sure the test procedures implemented are rigorous, reproducible and fully representative of the real constraints liable to affect the equipment throughout its operational life.

04

Benefit from a reliable and objective analysis of the results obtained from the laboratory tests, so as to rule with certainty on the real performance and robustness of the equipment.

05

Have at your disposal a formalised and usable summary document, enabling you to demonstrate the equipment's compliance to your internal stakeholders, your customers and the regulatory authorities.

Our method

A 5-step approach, from the framing of environmental constraints through to the DSQ.

  1. 01

    Analysis and specification of environmental conditions

    Foundational step that precisely defines the scope of constraints applicable to the equipment under consideration, consistent with its real installation and operating environment.

  2. 02

    Drafting of the environmental qualification plan

    Strategic document that formalises the chosen demonstration approach, the required tests and the associated acceptance criteria.

  3. 03

    Drafting of the environmental test procedures

    Guarantee of methodological rigour, reproducibility and traceability of each test performed.

  4. 04

    Analysis of laboratory test results

    Objective assessment of the equipment's compliance with the previously specified environmental requirements, based on the laboratory results.

  5. 05

    Drafting of the Qualification Summary Dossier (DSQ)

    Document consolidating all the data, technical analyses and conclusions produced by the approach: the cornerstone piece of the safety file.

Our strengths

  • Cross-cutting expertise covering the full set of nuclear environmental constraints: seismic, electromagnetic, radiological and climatic.
  • Recognised mastery in building qualification plans tailored to each piece of equipment and to its operating environment, with neither over-sizing nor approximation.
  • Proven ability to analyse and interpret laboratory test results, with a reliable, precise and well-argued reading of real-world performance.
  • A structuring, standards-based deliverable: the Qualification Summary Dossier (DSQ), a solid documentary reference for any demonstration of compliance with safety requirements.

Our offer

We support our clients throughout the environmental qualification process for their control & command equipment, from the initial analysis and specification of environmental conditions, through to the final drafting of the Qualification Summary Dossier (DSQ), by way of the definition of the qualification plan, the drafting of test procedures and the rigorous analysis of test results obtained in the laboratory.

Our references

Client
CEA

Support for the environmental qualification of control & command equipment for the experimental devices of the RJH

RCC-E · IEC 60780
Client
ONET Technologies

Support for the environmental qualification of control & command equipment for the loading-unloading machine (MCD) of the RJH

RCC-E · IEC 60780
Client
FRIOTHERM

K3 qualification of a control & command cabinet for a nuclear chilled-water unit function (DEL BIS)

RCC-E · CRT80.C.0.12
Training on the approach

Training course "The IEC 61513 standard and the qualification approach"

A 2.5-day training course delivered to the main stakeholders of the nuclear sector in France, covering the requirements applicable to safety I&C systems, including environmental qualification.

View the nuclear training courses
- Going further

Resources and related topics

Ready to grow your team's expertise?

Contact our team for a tailored quotation or to register for our 2026 training sessions.